Skip to content

PROTECTING YOUR WORLD

Painting Galvanized Steel:
Prep, Primers and
Duplex Life

How to prep new, weathered and white-rusted zinc, which primers actually grip it, and how many years a paint-over-galvanizing duplex system buys you.
Steel coating quotes

Galvanized steel to coat? Get the prep right first.

Tell us what the parts are, how old the galvanizing is and where they will live. We will match you with a certified ArmorThane applicator who preps zinc to spec before anything gets sprayed.

  • Item: structure, trailer, rack, tank or flashing
  • Age of the galvanizing and any white rust
  • Square footage or piece count
  • Exposure: salt, chemicals, impact, UV
Rather talk now? Call (417) 831-5090
Step 1 of 3
48 hrs
How long zinc stays "newly galvanized"
American Galvanizers Association
0.75 mil
Minimum profile after an SSPC-SP 16 brush-off blast
About 19 µm
12 hrs
Longest gap between prep and primer
Before new zinc oxides form
1.4–2.3x
Duplex multiplier on zinc life plus paint life
AGA duplex formula

Painting galvanized steel goes wrong for one reason more than any other: somebody treated the zinc like bare steel. Zinc is softer, smoother and far more reactive than steel, and its surface keeps changing for months after the part leaves the kettle. Match the prep to the age of the galvanizing and paint will hold for decades. Skip that step and it can peel off in sheets within a season.

Quick answer

Painting galvanized steel works when you prep the zinc, not the steel. Wash off oil and loose zinc salts, then give the surface tooth with a light sweep blast to SSPC-SP 16 (0.75 mil minimum profile) or an etching pretreatment, per ASTM D6386. Prime within 12 hours using an epoxy or a primer rated for galvanizing. Never use alkyd or oil-based paint; it reacts with zinc and peels.

Failure modes

Why paint fails on galvanized steel

We get called to a lot of jobs where painting galvanized steel went sideways: handrails, light poles, trailer frames, metal building trim. The paint is rarely the problem. Almost every one traces back to one of four things that happened before the first coat went on.

Chemistry

Alkyd and oil-based paint

Zinc reacts with the oil binder in alkyds and forms a soapy layer at the interface, a process called saponification. The film looks fine for a few months, then lets go all at once.

Surface

Too smooth to grip

Fresh hot-dip zinc is nearly slick. With no profile and no etch, even a good two-part epoxy has nothing to key into and fails a tape test.

Mill treatment

Passivation and quench salts

Many galvanizers quench parts in a passivating solution to stop storage stain. That film blocks adhesion and has to weather off, or be sanded or sweep blasted away.

Storage

White rust

Parts bundled tight and left wet grow a powdery white bloom, known as wet storage stain. Paint over it and that powder becomes the weakest layer in the system.

Tell the galvanizer before dippingIf the steel will be painted or powder coated, put it on the purchase order. The galvanizer can skip the quench, grind dross and drips flat and ship the parts dry. A two-minute phone call at the kettle saves a day of rework in the field.

Galvanizing is one layer of a corrosion plan. Our corrosion protection coatings page covers the systems that go over it, and preventing corrosion on steel structures walks through the bigger picture.

ASTM D6386

Prep depends on how old the zinc is

ASTM D6386 and the American Galvanizers Association sort galvanized surfaces by age, because the zinc changes as it reacts with air and moisture. Partially weathered zinc is both the most common condition you will meet and the hardest one to paint.

Surface conditionTypical ageWhat is on the surfacePrep that worksPrep effort
Newly galvanizedUp to 48 hoursMostly bare zinc, a thin oxide filmKnock down drips and high spots, clean if handled, then sweep blast or etchModerate
Partially weathered2 days to 1–2 yearsLoose zinc oxide and hydroxide, plus dirt and oilAlkaline wash, rinse, dry, then low-angle sweep blast or acid etchHigh
Fully weathered1–2 years and olderTight, insoluble zinc carbonateScrub, rinse and dry; a profile is usually not neededLow
Passivated or quenchedAny ageChromate or other passivation film, quench saltsConfirm with a spot test, then sand, sweep blast or let it weatherHigh
White rust presentAny agePowdery zinc hydroxide from wet storageNylon brush and ammonia for light stain, mild acid wash for heavy, then remeasure zincModerate
Based on ASTM D6386, AGA and KTA-Tator guidance. Tap a column heading to sort.

Cleaning mixes used in the field are simple, but the ratios matter:

  • Alkaline wash: about ten parts water to one part alkaline cleaner, brushed on or pressure washed below 1,450 psi.
  • Acid etch: roughly 25 parts water to one part acid. Rinse two to three minutes after application, then rinse again. The zinc turns a dull gray.
  • Solvent wipe: for spot oil and grease. Change rags often or you just move the oil around.
  • Household vinegar: it etches a little, but it does not remove oil and leaves residue if it is not rinsed well. Fine for a mailbox post, not for a spec job.
Planner

Prep method and duplex life in years

Pick the surface condition, set the zinc thickness and the environment, and the planner gives you the prep route plus how long the galvanizing lasts alone versus under paint. Default zinc is 3.9 mils, the ASTM A123 minimum average for structural shapes 1/4 inch and thicker.

Duplex math

Galvanized prep and duplex life planner

Zinc life = zinc thickness in µm ÷ the high end of the ISO 9223 zinc corrosion rate for the category (conservative). Duplex life = multiplier × (zinc life + paint life), the American Galvanizers Association formula. Multipliers used: 2.0–2.3 for C2 and C3, 1.8–2.0 for C4, 1.4–1.6 for C5 and CX.

0
Prep route
0
Zinc thickness, µm
0
Years, galvanizing alone
0
Years, painted duplex system

Life figures are time to first maintenance, not time to failure. Real sites vary; the AGA's Zinc Coating Life Predictor is the better tool when you have local climate data.

Coatings

Primers and topcoats that bond to zinc

For painting galvanized steel, the list of coatings that work is shorter than most paint aisles suggest. On anything that matters we want a two-part primer over a profiled surface, and a topcoat chosen for the abuse the part will see.

Workhorse

Epoxy primer

Polyamide or polyamidoamine epoxy over sweep-blasted zinc is the standard industrial answer. It chalks in sunlight, so outdoors it always gets a topcoat.

Light duty

Galvanized-rated acrylic

Waterborne acrylic bonding primers are fine on weathered fence, flashing and gutters. They are less forgiving on new, slick zinc that has not been etched.

Color and gloss

Aliphatic polyurethane

The usual finish over an epoxy primer outdoors. Holds color and gloss in UV far better than the epoxy underneath.

Impact and wear

Polyurea over primer

For trailers, hoppers, truck racks and grating that take a beating. Sweep blast, prime, then spray 40 mils or more. ArmorThane Primer 41 lists galvanized steel among its substrates.

Pretreatment only

Wash primer

A thin acid-bearing etch primer, kept to about 13 µm (0.5 mil). It gives new zinc tooth, but it is a pretreatment, never a finish.

Avoid

Alkyd and oil paint

Cheap and easy to buy, and the number one cause of peeling we see. It saponifies on zinc no matter how well the surface was cleaned.

Red rust showing through?Once you see red rust, the zinc in that spot is gone and you are painting steel again. Clean it to bare metal, repair with a zinc-rich coating per ASTM A780, then paint the whole piece as a duplex system.

Related: our metal primer guide compares primer types for every metal, the zinc rich primer guide covers repairing damaged galvanizing, and painting over rust handles steel that is already corroding. For the product itself, see Primer 41.

Field procedure

Painting galvanized steel, step by step

  1. Find out what you have

    Ask when it was dipped and whether it was quenched or passivated. A chromate spot test (ASTM B201) settles any doubt in a few minutes.

  2. Measure the zinc first

    Take magnetic gauge readings at several spots so you know how much zinc you start with. The AGA allows up to about 1 mil of removal during prep.

  3. Clean and rinse

    Alkaline wash, rinse with clean water and let it dry fully. Treat any white rust now, not after the blast.

  4. Profile with a light touch

    Sweep blast at 30 to 60 degrees with a soft abrasive (Mohs 5 or less, roughly 200 to 500 µm grit) and low pressure. You want a uniform dull satin look and 0.75 mil profile, not gray steel.

  5. Prime the same shift

    Get primer on within 12 hours of prep. Left longer, fresh zinc starts growing oxides again and you are back to step three.

  6. Topcoat and check

    Topcoat inside the primer's recoat window, check dry film thickness, and run an ASTM D3359 tape test on a test area before you call it done.

Do not blast it like bare steelSteel grit or coal slag at full pressure and 90 degrees will strip galvanizing in a couple of passes. You end up with bare steel under the paint and none of the zinc you paid for. Remeasure after blasting; if the readings dropped more than about a mil, back off the pressure.
Coat it once

Galvanized steel, prepped and sprayed to spec.

A certified ArmorThane applicator can quote your galvanized parts with the right prep, primer and topcoat for how they are used.

Contractors: become an ArmorThane applicator

FAQ

Galvanized painting questions

Is painting galvanized steel a good idea?

Yes, when it is prepped correctly. Paint over galvanizing forms a duplex system that typically lasts 1.4 to 2.3 times longer than the zinc and the paint would separately, added together. It also adds color, UV protection and, with polyurea, impact resistance.

What primer should I use on galvanized steel?

Use a two-part epoxy primer over a sweep-blasted or etched surface for industrial work, or a waterborne acrylic primer labeled for galvanizing on light-duty, weathered metal. Never use an alkyd or oil-based primer, which reacts with zinc and peels.

How long should galvanized steel weather before painting?

Fully weathered zinc, usually one to two years old, is the easiest to paint because its carbonate layer is tight and stable. You do not have to wait, though. New zinc can be painted right away with a sweep blast or etch pretreatment per ASTM D6386.

Why does paint peel off galvanized metal?

The usual causes are alkyd paint reacting with zinc, a surface too smooth for the primer to grip, passivation chemicals left from the galvanizer, or white rust under the paint. Each one is a prep problem, which is why the surface age matters so much.

Do you need to sand galvanized steel before painting?

New and partially weathered zinc needs some profile. A light sweep blast is best on larger work; sanding with a medium abrasive pad works on small parts. Take off as little zinc as possible, and no more than about 1 mil.

Can polyurea be sprayed over galvanized steel?

Yes. Clean and sweep blast the zinc, apply a primer rated for galvanized steel, then spray polyurea at the thickness the job needs, often 40 to 125 mils. It is a common upgrade for galvanized trailers, hoppers, truck racks and grating.

AT
Written by the ArmorThane technical team. We have manufactured polyurea, polyurethane and polyaspartic coatings and plural component spray equipment in Springfield, Missouri since 1989. Service life figures are estimates from published zinc corrosion rates; always follow ASTM D6386 and the coating data sheet.

Sources

  1. American Galvanizers Association, Preparing HDG for Paint. galvanizeit.org/specification-and-inspection/specifying-duplex-systems/preparing-hdg-for-paint
  2. American Galvanizers Association, HDG Corrosion Rates for ISO Categories C1–CX. galvanizeit.org/knowledgebase/article/hdg-corrosion-rates-for-iso-categories-c1-c5-x
  3. American Galvanizers Association, Duplex Systems: Synergistic Effect. galvanizeit.org/duplex-systems-galvanize-it-seminar/why-duplex/synergistic-effect
  4. American Galvanizers Association, Overview of ASTM A123/A123M. galvanizeit.org/knowledgebase/article/astm-a123-a123m
  5. KTA-Tator, Preparation of Galvanizing for Painting. kta.com/kta-university/preparation-galvanizing-painting
  6. Dunn-Edwards, How to Paint Galvanized Metal. dunnedwards.com/pros/blog/painting-galvanized-steel

Zinc underneath, armor on top.

ArmorThane applicators prep galvanized steel to ASTM D6386 and topcoat it with polyurea or polyurethane built for impact and weather. Contractors can add this work with our equipment and training, with no franchise fee and no royalties.

United States 417-831-5090 · Canada 780-444-6200

CONTACT US

REQUEST A QUOTE OR

BECOME AN APPLICATOR

ArmorThane has built a strong reputation over the past 30 years for producing high-quality, durable protective coatings.

group 115 660555abebfe4
Phone Number

Tel: 417.831.5090

group 115 1 660556c21395c
Email Us

moreinfo@armorthane.com

Step 1 of 3

We want to help you find the best ArmorThane applicator for your protective coating project. Please either fill out the request form below or call us toll free at 417-831-5090, any time Monday-Friday, 8:00 a.m. to 5:00 p.m. Central Standard Time.

RV Find An Applicator

Protective Coating Applications

Products

Applicator Opportunities

Knowledge Center

Galleries